Default Password, Login and IP for your Comtrend CT+ router. User Manuals and How to Factory Reset your Comtrend CT+ router. To perform a Comtrend router Login or Reset, follow these instructions. Router The Comtrend CT+ router with 54mbps WiFi, 4 mbps ETH-ports. This manual provides information related to the installation, operation, and application support for immediate service by email at [email protected] com.

Author: Yozshugore Kajicage
Country: Equatorial Guinea
Language: English (Spanish)
Genre: Art
Published (Last): 25 January 2016
Pages: 432
PDF File Size: 13.54 Mb
ePub File Size: 13.62 Mb
ISBN: 406-2-70116-997-1
Downloads: 94247
Price: Free* [*Free Regsitration Required]
Uploader: Yozshubar

Page 14 STEP 8: Need a new router? Select a Service User should select the service from the list.

The default setting for Incoming is Accepted. Follow the steps below to enable and view the system log. The following screen appears: This can be used to filter block or forward packets based on the originating device.

To load the factory default settings, hold the reset button down for at least 5 seconds. Lower integer values for precedence imply higher priority cct536 this entry relative to others.


Chapter 3 Login via the Web Browser This section describes how to manage the router via a Web browser via the remote end. Source Port port or port: Consult the table below for field descriptions.

For detailed descriptions, with examples, please consult Appendix A – Firewall. It usually does not matter which browser you choose to use. Enter the path to the image file location mamual the box below or click manul Browse button to locate the image file.


It should look something like this:.

Select a Service User should select the service from the list. Option Description Network It specifies the network authentication. Obtain an updated software image file from your ISP. By default, radio NICs passively scan all RF channels and listen for beacons coming from access points to find a suitable access point.

This ensures that your ports will remain open even after your device reboots. To add a parental control, simply click the Add button. Enter the subnet mask for the LAN port.

If pressed down for more than 20 seconds, the CT will go into a firmware update state CFE boot mode.

Our software does everything that you need to forward a port. Start the Internet browser and enter the default IP address for the device in the Web address field.

To create a group from the list, first enter the group name and then xomtrend from the available interfaces on the list. Don’t show me this message again.

Comtrend CT+ Default Password & Login, Manuals and Reset Instructions | RouterReset

Page of 50 Go. When this checkbox is Authentication selected, it specifies that a network key be used for authentication to the wireless network. Save button only saves the LAN configuration data.

Page 81 Channel Drop-down menu that allows selection of specific channel. All other frames on this interface are dropped. Or Custom Application Or User can enter the name of their choice. The following screen will appear when you click Tc536.

Use the Protocol dropdown box to select the protocol type of the ports you are forwarding. The DSL Settings dialog box comtred you to select an appropriate modulation mode. The user can then configure NAT-related features after the system comes up. The information contained herein is proprietary to Comtrend Corporation.


By default, it is disabled.

Comtrend Corporation CT-5374 User Manual

After entering your settings, select Next to display the following screen. This device contains a micro filter which removes the analog phone signal. Page 57 Filter Name Type a name for the filter rule. Click OK to submit these settings. Auto Quick Setup Note: It is important to setup a static ip address in the device that you are forwarding a port to.

GbETH Powered device connected to the associated port.

Daytime Parental Control This feature restricts access of a selected LAN device to an outside Network through the router, as per chosen days of the week and the chosen times. To add a dynamic DNS service, simply click the Add button. Choose Add to configure network traffic classes.

Comtrend Corporation CT-536+ User Manual

When the screen displays as below, click the Next button. Un-tick this checkbox to enable manual setup and display the following screen. Identifier for this Queue entry. A unique default user account is assigned with user name root and password