This paper model is Samaritan Revolver, Hellboy’s weapon, based on the Hellboy comic and film, the papercraft is created by UHU You can download this. This is the Samaritan gun, the big-barreled shooter that Hellboy uses only after muttering Samaritan Gun Papercraft [Way Nifty via ToyCyte]. We thought HAL was pretty cool, but this papercraft model of Hellboy’s Good Samaritan is ridiculously detailed, down to the hammer, cylinder and.

Author: Tashicage Akinogis
Country: Laos
Language: English (Spanish)
Genre: Automotive
Published (Last): 19 September 2018
Pages: 209
PDF File Size: 5.79 Mb
ePub File Size: 4.82 Mb
ISBN: 985-2-64366-633-7
Downloads: 55332
Price: Free* [*Free Regsitration Required]
Uploader: Kajir

D I’m in law enforcement, and if I didn’t know better, I’d say that thing was the real article! A warmer tone was mixed by adding a bit of mid brown with our original colour, and applied around areas of wear, like the hammer, rear and underside of the weapon.

Hellby mixed waterbased wood putty. Very impressive project MM, and a nicely detailed build thread! I buy this in large sheets from a stationers. I’ve glued pretty much the whole lot to 1mm card, just using white glue. I’ve made up a ring hllboy paper to the measurments of part 6, made by tightly winding strip of lightly glued paper around a suitably sized former in my case, a curtain roduntil it reached the required diameter, it then had its ends well soaked with superglue and sanded flat, making a VERY tough ring that should handle fair bit of abuse.

Appologies to UHU02, you are not to be doubted. The second layer paperceaft in much of the area not coverd by the first. I the painted most of it silver, as it would be difficult to reach with a brush papetcraft on.

It will need a few more coats, though. A trick for cutting such heavy laminations is to cut one layer paperceaft a time, stick it to the next layer and use it as a template to cut the next layer.

I’ve left the ends of the overlapping parts of the rifling loose so the can be glued over the seam when the rest of the liner is dry. I’ve carved the grips from balsa again, as I did with the Colt Navy, and as you can see from the pictures, I made a bit of a mistake and had to add a bit of extra material to the front ‘cos I took a bit too much off.


The whole lower section of the frame right to the back near the handle is pretty much solid laminated cardboard. Resources saved on this page: It would probably be different if I tried again…or maybe not. The Round ‘Recoil damper” is done just like the ring earlier, only longer.

What I hope to do is take a well designed model, which if made “straight from the printer’ will look something like this: All parts have been given a thourough coating of superglue, before sanding, primering, supergluing a bit more in spots, sanding some more etc etc. This all fell in a heap of course when I discovered my barrel wouldn’t fit.

Hellboy – Samaritan Revolver Free Paper Model Download

Find all posts by Plastic Bonsai. The techniques used in this thread ore not traditional card modelling techniques, but rather show how I build a card model using the design as basis for a much stronger and hopefully more realistic version. Just letting everybody know that we have approved the next 2 designs that will gunn part of our ongoing custom urban series vinylmation set.

Next picture shows a papercrafr of additions to the basic model, that are aesy to add and easily visible in photo’s of the real one.


I was never really great at papercrafts. It’s really starting to take shape uellboy. Actually, this model is very well suited to this building approach, with all its flat sides and sharp angles, and simple colouring.

This was quite an engineering feat, and way beyond my normal scope as I’m usually quite happy with non-working replicas. The BPRD logos were picked out in a dirty silver colour ; and highlighted and shaded a bit for a bit extra life ; I’m still trying to spot the point in gub build where the card model is replaced with the real thing!

Bullets And Paper Cuts: Hellboy’s Samaritan – Geekologie

On second thought, maybe just use the force to guide you. If you ever leave the house with it, make sure it’s in a case. With each new set comes another opportunity to go on the hunt, to be the first to blind box a chaser or variant and if nothing else but for the thrill of opening just one more box….


I didn’t, and now all my wonderful rifling is yuckky at the top where I had to cut 3mm out of the tube A superglue accelerator is also usful, but not palercraft important. I’ve altered the method of anchoring the grip because it suited the materials I’m using, not because the suggested method is inadequate.

This method gives an amazingly strong component, much stronger than an equivelent plastic part. So I’ve added extra rings in the middle, and gone with simple tubes at the front, and horseshoe shapes in the top, but this leaves me with a seam accross the middle of the chambers that the “proper” design wouldn’t.

Not a fault of the model, per-se, just a personal choice. You can download the pieces from the link. I use a auto primer matt black which dries satin, for some odd reason because it dries much tougher hellbboy more durable than a cheap generic spraycan.

Find all posts by ThunderChild. Anyhoo, after the rather happy way the colt is turning out, Papercarft decided to go for something even chunkier, in the manner of UHU02’s Hell Boy Samaritan Gun. Send a private message to ThunderChild.

The swivelling arm at the back of the weapon that swings upwards to open the cylinder break is incorrect. Check out the video after the jump…. I’ve gone the extra and moved up to spray putty a type of thick, heavy build body spray, available from auto parts suppliers for the main papercfaft, as there’s no detail to obscure yet, and it will hopefully make the job quicker.

Second, a bit of a bulge at the rear of the recoil compensator tube. Try doing that with your regular card model! Cheapest you can get. Something the instructions would have you do is leave one side of the frame loose so you helllboy fit a retaining pin inside and then close it up. It’s puts me in paperfraft of 12 guage shotgun sort of size.

I’m working on more of the details today, the BPRD logos on the grip in particular.